| 引用本文: | 李石保,陈朝辉,王忠义,等.聚甲基丙烯酸甲酯-氧化锆复合材料的制备.[J].国防科技大学学报,2005,27(4):32-36.[点击复制] |
| LI Shibao,CHEN Zhaohui,WANG Zhongyi,et al.The Preparation of PMMA-Zirconia Composites[J].Journal of National University of Defense Technology,2005,27(4):32-36[点击复制] |
|
| |
|
|
| 本文已被：浏览 7241次 下载 5772次 |
| 聚甲基丙烯酸甲酯-氧化锆复合材料的制备 |
| 李石保1, 陈朝辉1, 王忠义2, 胡海峰1, 唐立辉2, 郑文伟1 |
|
(1.国防科技大学 航天与材料工程学院，湖南 长沙 410073;2.第四军医大学 秦都口腔医学院，陕西 西安 710032)
|
| 摘要: |
| 将氧化锆纳米粉体冷等静压成型，经部分烧结制备成具有多孔网状结构的部分烧结体，然后经真空浸渍，将预聚甲基丙烯酸甲酯渗透入部分烧结体的开孔中，原位聚合，制备出聚甲基丙烯酸甲酯—氧化锆有机—无机复合材料。结果表明：预聚甲基丙烯酸甲酯经真空浸渍能完全浸入部分烧结陶瓷的开孔中并固化。当部分烧结体相对密度为63%～82%时，复合材料的弯曲强度为154～287MPa、断裂韧性为3.68～4.81MPa·m1/2；与部分烧结体比较，有明显提高。该复合材料经牙科CAD/CAM系统切削加工，可制作牙科修复体。 |
| 关键词: 有机—无机复合材料 牙科材料 聚甲基丙烯酸甲酯-氧化锆复合材料 制备 |
| DOI： |
| 投稿日期：2004-12-25 |
| 基金项目: |
|
| The Preparation of PMMA-Zirconia Composites |
| LI Shibao1, CHEN Zhaohui1, WANG Zhongyi2, HU Haifeng1, TANG Lihui2, ZHENG Wenwei1 |
|
(1.College of Aerospace and Materials Engineering, National Univ. of Defense Technology, Changsha 410073, China;2.Qindu Stomatology College, Fourth Military Medical University, Xi'an 710032，China)
|
| Abstract: |
| Partially sintered zirconia ceramics (PSZC) were prepared via isostatic pressing and partially sintering，with zirconia nanopowder as the raw materials. PMMA-Zirconia organic-inorganic composites were prepared by vacuum infiltration of the prepolymerized MMA into the PSZC, followed by in-situ polymerization. The results show that prepolymerized MMA immerged fully into the open pore of PSZC and polymerized. When the relative density of PSZC is within the range of 63%～82%, the composites have a three-point bending strength of 154～287MPa, fracture toughness of 3.68～4.81MPa·m1/2 ,which are much higher than those of PSZC. The composites can be machined by dental CAD/CAM system to manufacture dental restoration. |
| Keywords: organic-inorganic composites dental materials PMMA-zirconia composites preparation |
|
|
|
|
|
