| 引用本文: | 田野,戴一帆,石峰,等.单晶硅反射镜激光能量吸收系数与衬底表面质量的关联.[J].国防科技大学学报,2015,37(6):26-29.[点击复制] |
| TIAN Ye,DAI Yifan,SHI Feng,et al.Correlation between substrate surface quality and laser energy absorption rate for mono-crystalline silicon reflector[J].Journal of National University of Defense Technology,2015,37(6):26-29[点击复制] |
|
| |
|
|
| 本文已被：浏览 10760次 下载 6972次 |
| 单晶硅反射镜激光能量吸收系数与衬底表面质量的关联 |
| 田野1,2, 戴一帆1,2, 石峰1,2, 彭小强1,2, 韩凯3, 朱志武1,2, 万稳1,2 |
|
(1.国防科技大学 机电工程与自动化学院， 湖南 长沙 410073;2.
2.超精密加工技术湖南省重点实验室， 湖南 长沙 410073;3.国防科技大学 光电科学与工程学院， 湖南 长沙 410073)
|
| 摘要: |
| 高能激光系统中，单晶硅基底反射镜的能量吸收系数是影响系统性能的关键指标。衬底加工质量对镀膜后元件激光能量吸收系数影响显著。通过测试不同衬底粗糙度、划痕密度的单晶硅反射元件，分析衬底表面典型加工特征（粗糙度、划痕）对激光能量吸收系数的影响规律，认为粗糙度与吸收系数正相关，粗糙度均方根从0.668nm降低至0.345nm会使吸收系数降低28.0%。少量划痕对吸收系数的直接影响并不明显，吸收系数均值变化在3.1%以内。但表面划痕会诱发激光损伤，划痕密度较大时会引起后续能量吸收持续增大，辐照400s后，吸收系数较辐照100s时增大18.3%。 |
| 关键词: 单晶硅 激光能量吸收系数 衬底表面质量 |
| DOI：10.11887/j.cn.201506006 |
| 投稿日期：2015-08-26 |
| 基金项目:国家自然科学基金资助项目（91023042） |
|
| Correlation between substrate surface quality and laser energy absorption rate for mono-crystalline silicon reflector |
| TIAN Ye1,2, DAI Yifan1,2, SHI Feng1,2, PENG Xiaoqiang1,2, HAN Kai3, ZHU Zhiwu1,2, WAN Wen1,2 |
|
(1.College of Mechatronics Engineering and Automation, National University of Defense Technology, Changsha 410073, China;2.2. Hunan Key Laboratory of Ultraprecision Machining Technology, Changsha 410073, China;3. College of Optoelectronic Science and Engineering, National University of Defense Technology, Changsha 410073, China)
|
| Abstract: |
| In high energy laser systems, the energy absorption rate (EAR) of mono-crystalline silicon reflector is a vital index in the term of elements quality. The substrate process quality affects the EAR of coated optics dramatically. The surface roughness and scratch density for a series of silicon optics were measured. Based on the result, the co-influence and relationship between surface characteristic and EAR were analyzed. It is indicated that, surface roughness level is positively correlated to EAR and decides the global average rate of the entire surface. When the root-mean-square of roughness falls from 0.668nm to 0.345nm, the EAR decreases by 28.0%. In contrast, few scratches do not distinctly raise the EAR, the fluctuation is less than 3.1%. However, the surface scratch may generate laser-induced damage. Furthermore, when the scratch density is large enough, the subsequent EAR will grow constantly, for example, the amplitude reaches 18.3% after the 400s irradiation, compared with 100s irradiation. |
| Keywords: mono-crystalline silicon laser energy absorption rate substrate surface quality |
|
|
|
|
|
