| 引用本文: | 武新峰,刘观日,雷勇军,等.基于参数化建模的包带式星箭连接结构优化设计.[J].国防科技大学学报,2013,35(5):6-12.[点击复制] |
| WU Xinfeng,LIU Guanri,LEI Yongjun,et al.Optimizing design of clamp band joint based on parameter modeling method[J].Journal of National University of Defense Technology,2013,35(5):6-12[点击复制] |
|
| |
|
|
| 本文已被：浏览 8657次 下载 6988次 |
| 基于参数化建模的包带式星箭连接结构优化设计 |
| 武新峰1, 刘观日1,2, 雷勇军1, 李谨1 |
|
(1. 国防科技大学 航天科学与工程学院，湖南 长沙 410073;2.
2. 北京宇航系统工程研究所，北京 100076)
|
| 摘要: |
| 采用MSC.Patran参数化建模和遗传算法进行包带式星箭连接结构优化设计。首先给出了包带连接结构二维轴对称模型优化设计过程中涉及的V形卡块刚度等效、包带预紧力模拟和载荷施加方法，以及强度和刚度约束条件、优化目标等内容；然后以某直径为3m的包带连接结构为例进行了优化设计，并分析了对接框内延伸段长度和端头高度对应力及变形的影响；最后建立三维有限元模型进行静力分析。结果表明（1）该方法适用于包带连接结构的优化设计；（2）增加对接框内延伸段长度和端头高度能够提高整体连接刚度；（3）三维有限元模型与轴对称模型计算结果一致，验证了轴对称模型分析方法的正确性，以及V形卡块等效和预紧力模拟方法的有效性。 |
| 关键词: 包带连接结构 参数化建模 遗传算法 优化设计 |
| DOI： |
| 投稿日期：2013-02-27 |
| 基金项目:国家自然科学基金重点资助项目（11132012）；国家自然科学基金资助项目（11272348） |
|
| Optimizing design of clamp band joint based on parameter modeling method |
| WU Xinfeng1, LIU Guanri1,2, LEI Yongjun1, LI Jin1 |
|
(1. College of Aerospace Science and Engineering, National University of Defense Technology, Changsha 410073, China;2.
2. Beijing Institute of Astronautical Systems Engineering, Beijing 100076, China)
|
| Abstract: |
| A new application based on the parameter modeling method of MSC.Patran and generation algorithm was proposed to design the clamp band joint. First, finite element techniques for 2-dimension axisymmetric analysis of clamp band joints were developed, including the modeling of V-clamp, strap pre-tension and loads, and the optimizing constrains and objectives were also introduced. Then a clamp band joint with the diameter being 3m was designed via the presented method. Finally, a 3-dimension finite element model of the designed clamp band joint was established and analyzed. It indicates that the method is applicable to the design of clamp band joints, that the connective stiffness is strengthened by increasing the length and height of the inner ring of the interface rings, and that the modeling method is proved to be valid by the agreements of the finite element analysis results of 2-D model and 3-D model. |
| Keywords: clamp band joint parameterized modeling method generation algorithm optimizing design |
|
|
|
|
|
