| 引用本文: | 俞小华,董健年,王浩,等.脉冲电抗器结构应力测量.[J].国防科技大学学报,2016,38(3):124-129.[点击复制] |
| YU Xiaohua,DONG Jiannian,WANG Hao,et al.Measurement of stress in pulsed reactor structure[J].Journal of National University of Defense Technology,2016,38(3):124-129[点击复制] |
|
| |
|
|
| 本文已被：浏览 7988次 下载 6498次 |
| 脉冲电抗器结构应力测量 |
| 俞小华1,2, 董健年1, 王浩1, 陈远晟1, 杨希1 |
|
(1.南京理工大学 能源与动力工程学院， 江苏 南京 210094;2.
2.中国人民解放军73198部队， 江苏 南京 210009)
|
| 摘要: |
| 为了对高压脉冲放电时电抗器结构受力及电流密度分布规律进行分析，使用电阻应变片对电抗器铜带进行应力测量。利用厚壁筒受压模型对应力测量系统的结果进行计算，设计内置气囊增压法来等效铜带上的应力对测量系统进行标定，并对标定实验数据进行验证。使用半桥补偿电路、屏蔽线及电桥盒共地的方法来减小脉冲电磁干扰及测量回路中寄生电阻和电容带来的电气干扰。实验结果表明：同一测量点处的环向应变峰值比轴向应变峰值大，边缘处的应变大于中心处的，需要在电抗器铜带边缘处加强外包约束。根据应力测量结果推断：铜带边缘处电流密度约为中心处电流密度的1.2倍。 |
| 关键词: 脉冲电抗器 电阻传感器 轴向应变 环向应变 电流密度 |
| DOI：10.11887/j.cn.201603021 |
| 投稿日期：2015-06-09 |
| 基金项目:国家自然科学基金资助项目（51405235）；装备预先研究资助项目（51326020302） |
|
| Measurement of stress in pulsed reactor structure |
| YU Xiaohua1,2, DONG Jiannian1, WANG Hao1, CHEN Yuansheng1, YANG Xi1 |
|
(1. College of Energy and Power Engineering, Nanjing University of Science and Technology, Nanjing 210094, China;2.
2. The PLA Unit 73198, Nanjing 210009, China)
|
| Abstract: |
| In order to analyze the structure stress and the current density distribution on the pulsed reactor in the course of working, the test on the stress was designed. The hoop stress on both the edge and the center of copper belt was obtained by the resistance transducer. The stress result was validated by calculating the thick wall cylinder model with the inflation pressure. To calibrate the stress value, the copper belt coil with a ballonet inside was designed. The half-bridge circuit, electrical grounding of the bridge cases and shielding wires were designed and put in practice to reduce the pulsed electromagnetic interference. The disturbance generated by the parasitic resistance and the stray capacitance was reduced by electrical grounding of the bridge cases. The experiment results show that the hoop strain is larger than the axial strain, the strain on the edge is larger than the strain in the center. Reinforcement should be applied on the edge of the copper belt. And it can be speculated that the current density on the edge is about 1.2 times near the center. |
| Keywords: pulsed reactor resistance transducer axial strain hoop strain current density |
|
|
